Ussc 1110 Ussc
When Installing your heater in an exterior wall
• Selectawalltotheexteriorofthebuilding.iswallshouldhavethere-
quired clearance to combustibles inside and out mentioned earlier in this
manual. Make certain that electrical wires, conduit, water or gas pipes do
not pass through the area you have selected
• USSCsuggestthefollowinginstallationillustratedtotheright,however,
you may frame the hole cut out to your discretion. A sturdy base for the
heater to rest should be established.
• Atthedesiredheight,marktheholelocationforyourheater.Measureand
cut the appropriate size hole for your installation. e cut out should border
a wall stud. e next wall stud will need to be cut.
Build a frame of 2 x 4’s at the dimensions suggested and secure it in place
by attaching it to the available studs.
• Beforeinstallingtheheater,installtheKnee/SupportBraces.
• Installtheknee/supportbracessupplied.Seethepreviouspageforinstallation.Youmayusethehardwaresuppliedorpurchase
the appropriate fasteners from your local hardware store for the type of material you are securing into.
• Sealaroundtheheaterwithsiliconeorcaulkingtoprotectagainsttheweather.
[648mm]
[572mm]
[356mm] [432mm]
WARNING! DO NOT INSTALL IN A SLEEPING ROOM
CAUTION! THE STRUCTURAL INTEGRITY OF THE MOBILE HOME FLOOR, WALL, AND CEILING/ROOF MUST
BE MAINTAINED.
• eheatermustbepermanentlyattachedtothewall.
• eheatermustbeelectricallygroundedtothesteelchassisofthemobilehomewith8GAcopperwireusingaserratedorstar
washer to penetrate paint or protective coating to ensure grounding.
• Whenmovingyourmobilehome,theheatermustberemovedwhilethemobilehomeisbeingrelocated.Aerrelocation,heater
may be reinstalled and securely fastened.
• Checkwithyourlocalbuildingocialsasothercodesmayapply.
Mobile Home Installation Requirements
Wall Installation
How your heater works
Your Eco-Aire pellet heater operates on a timer based auger fuel feed system, that is controlled by a digital circuit board. e fuel is
delivered from the auger into a burn pot, which is the vessel where the combustion process takes place. Based upon the heat ranges
(1-5), the heater will feed the appropriate amount of fuel to reach a set temperature range. Note that the amount of heat produced
by the heater is proportional to the rate of the fuel that is burned. Your heater is equipped with an automatic ignition system that
should ignite the fuel within 5-10 minutes from pressing the ON button. As pellets fall into the burn pot and ignite, outside air is
drawn in to feed the re by a combustion blower. e post combustion gases are then pulled through the heat exchanger as they are
traveling out the exhaust. As the heater warms up, room air is circulated around the heat exchanger by means of a room air blower,
distributing warm air into the room.
Because a forced dra pressure is required for the combustion process inside your heater, it is extremely important that the exhaust
system be properly maintained. And, that when operating your heater, you make sure that the viewing and combustion doors are
properly closed and/or sealed.
Turning the heater ON/OFF, as well as adjustments for the fuel feed rate is performed by pressing the appropriate button(s) on the
control panel which is located on the front, lower le-hand corner of your heater.
ON/OFF
• Pressingthe“ON”buttononthecontrolpanelwillbeginthestart-upsequencefortheheater.Fuelwillbegintofeedthroughthe
auger feed system then ignite aer approx. 5 minutes.
• Pressingthe“OFF”buttononthecontrolpanelwillcausetheheatertoenteritsshut-downsequence.efuelfeedsystemwill
stop pulling fuel from the hopper and, once the re goes out and the heater cools down, the fans will stop running.
HEAT RANGE
• Pressingthe“HeatRange”arrows,upordown,willadjusttheamountoffuelbeingdeliveredtotheburnpot.
• eexhaustblowerwillstart.Notethatthisappliancepulsestheexhaustblowerinordertoachievetheproperairtofuelratio,
and to also aid in the cleaning of the burn pot.
• Oncetheheaterreachesasettemperature,theroomfanwillcomeon.
LIGHT (LED) INDICATORS
• HeatRangeLED- displaystheselected heatsetting.
Number “1” LED lights to display that there is power to
unit even if the heater is o.
• DoorSwLED-lightswhenfrontviewingdoorisopened
or if the hopper lid is raised.
• PressSwLED -lightsif pressureislostinsidethe
combustion chamber. (See “Errors”)
• ELED-OperationalError(See“Errors”)
• ONLED-Flashesinstart-upmode.OnsolidduringRun
mode
• OFFLED-Flashesduringshutdownmode
Control Panel Overview
Understanding your heater
Kommentare zu diesen Handbüchern