Eco-Aire 2402 Bedienerhandbuch PDF herunterladen (Seite 5)

Ussc 98 Ussc

When Installing your heater in a window

• Selectawindowofadequatesizeandwiththeappropriateclearances

needed for a safe installation. e mounting hardware supplied is

designed for the appliance to be installed in the approximate center

of the window. You will need to provide the attaching hardware, (i.e.

screws, wall anchors, etc.) of which should be suitable for mounting

to the outside surface of your home or structure. You may choose

to utilize the supplied mounting system or a conguration of your

own. However, U.S. Stove shall not be liable for faulty mounting

congurations.

• Dependingonyourapplication,asolidrestingsurfacewillneedto

be established on the window sill. If your selected window’s bottom

ange rises above the sill, a board will need to be placed and should

be level with or just rise above that ange. Use the illustration to

the right for reference.

• esuppliedsupportbracketswillneedtobemountedbeforein-

serting the heater into the window. ese pieces will mount to the

outside of the home or structure.

• AssemblethetwoKneeBraces to theRetentionBracketusinga

washer (d) and nut (e) for each side. Tighten the nuts then back

them o to allow the bracket to slide back and forth along the knee

braces.

• Usingacarpenter’slevelorastraightedge,determinetheheightof

the retention bracket in relation to the resting surface of the heater.

Once you’ve determined that mark, locate the mounting assembly

1/4” lower to allow for precipitation runo.

• AttachtheKneeBracestothehomeorstructureusingthehardware

that you have determined suitable for your application.

• Onceyou’vestabilizedtheKneeBraces,you’rereadytoinsertthe

heater into the window/opening. Slide the heater thru the window

or opening. Insert item “a” in the center hole of the bottom but don’t

tighten fully. Allow item “a” to engage the SLOT in the retention

bracket as shown in the illustration to the right. Slide the heater into

the window opening until it stops. e heater should either stop on

the window sash at the back of the hopper lid or on the window sill

when it reaches the fan enclosure, whichever comes rst.

• Aligntheholesintheretentionbracketandheaterbottom.Insert

a washer (b) and bolt (c), and tighten.

• Tightenthetwonuts(e)onthekneebraces.

• Usingthewindowsillbrackets,mountthemtothesideoftheheater,

using the existing cabinet screws, then to the top of the window sill

with the screws provided. See illustration on the following page.

• Lowerthesashontothetopoftheheaterandproceedtoinstallthe

window insulation/ller panels.

WINDOW Sill MOUNT-

ING BRACKETS

Window Installation Window Installation

SLOT

Retention

Bracket

Knee

Braces

Installing the ller panels

• Beginbyassemblingtheleandrightsidellerpanelstogether.SlidepartA

into part B; Notice the range of adjustment. If the openings on each side of the

heater exceeds this range, you will have to ll the gap by other means necessary

to keep the window/opening weather tight. Otherwise, proceed.

• Placethepanelassemblyagainstthebottomofthewindowsashandbottomof

the window frame. Slide apart the two sections until the ange on part A meets

the inside of the window frame and the ange on part B meets the side of the

heater. Using a drill with a 5/16” socket bit, drive the self-tapping screw through

the hole in part A into part B. is sets the width of the panels.

• Peelawaytheprotectivecoatingfromthetwo-sidedtapeontheangesand

adhere it to the window and framing.

• Measurethellerpanelwidthandcutthefoaminsulationtosize.Peelawaythe

coating on the tape strips and apply the foam to the panels.

• Finishtheinstallbysealingaroundtheoutsideoftheheaterandllerpanels

with a weatherproong silicone sealant.

TWO-SIDED TAPE

SCREW

CUT-TO-FIT

1 2 3 4 5 6 7 8 9 10 11

Kommentare zu diesen Handbüchern

Keine Kommentare

Eco-Aire 2402 Bedienerhandbuch Seite 5

Kommentare zu diesen Handbüchern